Best Victron Energy products in the Battery accessories category

On this page you'll find a ranking of the best Victron Energy products in this category. To give you a quick overview, we've already ranked the most important information about the products for you.

1. Victron Energy RS485 to USB Interface 5m ASS030572050 Adapter cable

The 5m USB to RS485 interface cable from Victron Energy for connecting the ET112 or ET340 energy meter to the Color Control GX system control monitor or the Venus GX system monitoring. This text is machine translated. 

2. Victron Energy Battery switch Victron ON/OFF 275A

This switch offers a number of unique functions. The highlight is the Contour Locking System, which enables it to be locked as a stand-alone unit or together with other switches. This text is machine translated. 

3. Victron Energy Busbar Victron 150A 4P + cover

The Busbar connecting rail reduces the amount of cabling required when mounting several modular fuse holders in parallel, thus simplifying installation.

4. Victron Energy BPC900200014 Adapter cable

The 2 meter extension cable is an accessory for the Blue smart IP65 charger with DC connection. This text is machine translated.

5. Victron Energy Argofet 200-3, 3 batteries 200A

Argo FET Battery Separation

Similar to isolating diodes, FET isolators allow simultaneous charging of two or more batteries through an alternator or through a charger
connection without connecting the batteries together. Discharging the on-board battery does not result in simultaneous discharging of the starter battery. In contrast to isolating diodes, there is practically no voltage loss with FET isolators. The voltage drop is less than 0.02 volts at low currents and only 0.1 volts at higher currents. With ARGO FET battery isolation, no voltage increase is required. However, one should pay attention to short cable lengths and sufficient cross-sections.

Generator start-up excitation
Some generator types require a DC voltage at the B+ pole for start-up excitation. On the one hand, there is a direct cable connection between the battery and the generator. On the other hand, however, the isolating diode prevents the current from flowing back, so that the generator does not start. The new Argofet battery isolator has a special current-limited connection for start excitation when the generator is started.
 

6. Victron Energy Battery protection Smart Battery 12/24V 65A

Smart BatteryProtect disconnects the battery from the less important consumers before it is completely discharged (which would damage it) or before it no longer has enough energy to start the engine. 

7. Victron Energy Argo

Battery isolating diodes enable simultaneous charging of several batteries from one power source without the individual batteries being connected to each other. For example, the on-board battery can be charged without simultaneously discharging the starter battery. In addition, the use of modern Shottky diodes keeps the voltage loss low. It is approx. 0.3 V at low currents and approx. 045 V at rated current. 

8. Victron Energy Adapter cable Victron

Required to connect Victron devices with VE.Dirct connector via USB to notebook or computer.

9. Victron Energy RJ45 splitter ASS030065510 adapter cable

This splitter is used to connect the Victron MultiPlus 500VA - 1600VA devices in parallel and three-phase configurations or in other installations where multiple VE.Bus ports are required. This text is machine translated. 

Victron Energy RJ45 splitter ASS030065510 adapter cable
Battery accessories
–12%
32.31was 36.62

Victron Energy RJ45 splitter ASS030065510 adapter cable

10. Victron Energy VE.Can to CAN-bus BMS type A ASS030710018 Connecting cable

Specifications: .Product size (length): 1.8 m - Product type: Cable.

Victron Energy VE.Can to CAN-bus BMS type A ASS030710018 Connecting cable
Battery accessories
29.–

Victron Energy VE.Can to CAN-bus BMS type A ASS030710018 Connecting cable