Best selling Water cooling connection accessories from EKWB

This page always stays fresh and updates automatically.

1. EKWB EK-Cable PWM Fan Adapter for GPU

The EK Water Blocks EK-Cable PWM Fan Adapter allows you to connect your graphics card (provided it has the appropriate port) to PWM-controlled fans. This enables the cooling performance of the additional fans to be adjusted according to the PWM signal and the temperature of the graphics card, resulting in significantly more efficient cooling. The black cable features a 4-pin PWM fan socket and a 4-pin PWM fan connector. It is 50 cm long, allowing for a convenient connection to compatible components.

Note: The power limit of the fan connection on modern graphics cards is capped at two amps.

Technical details:
- Length: 500 mm
- Color: Black
- Connections:
- 1x 4-pin PWM fan connector
- 1x 4-pin PWM fan socket. 

2. EKWB EK-Loop Leak Tester Flex

With the EK-Loop Leak Tester Flex from EK Water Blocks, accidents caused by a leaking water cooling system are a thing of the past. Traditionally, leaks were only discovered after some time and only after filling the system. With the EK-Loop Leak Tester Flex, you take a safe approach. This way, not only does your hardware stay dry, but so do your eyes. Technical details: Main color: Black, Accent colors: Gold, Gray, Silver. 

What our customers think

Pro

  • Pump!
  • Easy to operate
  • High quality feel

3. EKWB Bitspower seal ring set for 1/4 inch thread

Water and electronics are known to not mix well. To ensure that the separation between these two areas remains 100% intact, especially in beloved water cooling systems, the sealing rings at the connections should be replaced regularly.

Similar to vehicle tires, these sealing rings have a long lifespan but lose elasticity over time and become brittle. Just as this can lead to reduced grip on the road and potentially cause accidents, it can also create problems in water cooling systems if a system becomes leaky.

In addition to the contact of water with electronics, the decreasing water pressure, increased noise due to air within the system, and potentially a total cooling failure pose significant risks to expensive hardware.

With this set of many O-shaped sealing rings, even extensive systems can be completely refurbished. The inner diameter is designed for G1/4 inch external threads. This is the most common thread standard, allowing for the sealing of nearly all screw threads with few exceptions. Be proactive!

Technical details:
- Material: Rubber
- For: G1/4 inch external threads
- Contents: approximately 50 pieces. 

4. EKWB EK-Pro Manifold 2CPU 6GPU - Acetal

The EK-Pro Manifold is a specially designed distribution block for multiple water coolers in workstation systems. It provides perfect coolant distribution through the use of multiple G1/4-inch inlets and outlets. The EK-Pro Manifold 2CPU 6GPU can connect and supply water to two CPU and six GPU water blocks in parallel or semi-parallel setups.

The block features a full acetal body, stainless steel end caps, and nickel-plated brass plugs. Pre-assembled, it can be used immediately. The EK-Pro Manifold comes with a universal mounting system that can be utilized in various scenarios. The steel mounting plate is equipped with mounting holes for 120mm and 140mm fan positions.

Technical details:
- Dimensions: 266 x 57 x 36 mm (L x W x H)
- Color: Black
- Material: Acetal, Metal
- Threads: 20x G1/4 inch
- Maximum number of CPUs: 2
- Maximum number of GPUs: 6
- Delivery includes:
- 1x EK Water Blocks EK-Pro Manifold 2CPU 8GPU
- 1x Screw and plug set
- 1x 6 mm and 2.5 mm hex key
- 1x Mounting frame

Note: Caution! Components of a water cooling system should only be used with the same materials to avoid corrosion and damage. The distribution block does not serve as a reservoir. Only a total of 7 plugs are included in the delivery. 

5. EKWB EK Loop Modulus HT Bending Tool 12mm 3831109816103

With the EK Water Blocks EK-Loop Modulus, you can easily bend hard tubes for your custom water cooling system.

The block made of POM plastic features two bending radii for PETG and acrylic tubes. With these, you can bend your hard tubes at either 90 or 45 degrees. Simply heat them gently and then place them in the respective mold.

Technical details:
- Color: Black
- Material: POM plastic
- Supported outer diameter: 12 mm
- Delivery includes: 1x EK-Loop Modulus Hard Tube Bending Tool 12 mm. 

6. EKWB EK-Scalar Quad 2-Slot

The EK-Scalar Quad 2-Slot is designed to connect four graphics cards equipped with EK-Vector or EK-FC water coolers. The terminal connects directly to the respective VGA coolers, and additional fittings, seals, tubes, or hoses are required.

In this version, the terminal is made of transparent acrylic. The flow through this bridge is parallel. Therefore, two tubes run vertically through the connector, with water entering on one side, splitting, and flowing through the four VGA coolers, before being discharged on the other side. Advantage: All coolers receive evenly cold water. Disadvantage: However, this results in lower pressure.

Note: The terminal is only compatible with EK-Vector or EK-FC series water coolers.

Technical details:
- Material: Acrylic
- Color: Transparent
- VGA cooler connections: 4x
- Thread: G1/4 inch
- Delivery includes:
1x EK-Scalar Quad 2-Slot - Acrylic
2x G1/4-Plug
1x Mounting mechanism. 

7. EKWB EK Loop Metal Tube Cutting Tool 3831109861783

The EK Loop Metal Pipe Cutting Tool is a small, handy tool specifically designed for cutting metal pipes. It is compatible with various metal pipes made of copper, brass, and nickel. The maximum size compatibility of the cutter is 32 mm outer diameter.

This allows you to shorten rigid metal pipes for your custom loop. It is made of stainless steel and can be adjusted to fit any pipe size commonly used in water-cooled PCs with hard tubing. It pairs perfectly with EK Loop metal pipes to cut them to the exact fit and superior aesthetics. 

8. EKWB EK-Torque STC-16/10 color ring - 10 pack

Decorative ring for the Compression Fittings Torque-STC from EK Water Blocks, made of anodized aluminum.

9. EKWB EK-Pro Manifold 2CPU 4GPU Distributor - Acetal

With the EK-Pro Manifold 2CPU 4GPU, EK Water Blocks offers a distribution block for workstations. This allows for the connection of up to two CPU and four GPU water coolers in a parallel or semi-parallel configuration. The manifold is made of acetal with end caps made of stainless steel and nickel-plated brass fittings, and it can be mounted on any 120mm or 140mm fan slot using the included mounting plate.

In combination with the separately available EK-Pro Quick Disconnect Kits for graphics cards and processors, individual water-cooled components can be quickly swapped out without needing to drain the coolant from the entire cooling loop.

Note: Please be aware that the manifold includes seven sealing plugs. The EK-Pro Manifold 2CPU 4GPU has a total of 18 inlets/outlets.

Technical details:
- Dimensions (without mounting plate): approx. 204 x 54 x 36 mm (W x H x D)
- Material: Acetal, steel, brass (nickel-plated)
- Connections: 18x G1/4 inch
- Scope of delivery:
- 1x EK-Pro Manifold 2CPU 4GPU
- 1x Allen key (6 mm)
- 1x Allen key (2.5 mm)
- 1x Mounting plate
- 4x M4 screws (6 mm, DIN7984)
- 7x Sealing plugs. 

10. EKWB EK-Loop Standoff M4 / M2.5 x 2.5, 15 pieces

With the EK-Loop Standoff M4 / M2 x 2.5 screws, you can mount your EKWB water cooler on your CPU, GPU, or motherboard.

Technical details:
- Number of standoffs: 15 pieces
- Color: Gray, Silver
- Compatibility: GPU, CPU, and monoblocks from EKWB. 

Product order
See all products

Relevant lists