Best selling Actuators from Eltako
On this page you’ll find a ranking of the best Actuators from Eltako. To give you a quick overview, we’ve added the most important product details. This page always stays fresh and updates automatically.
1. Eltako Impulse switch ES61-UC
Eltako pulse switch UC. 1 potential-free normally open contact 10A/250V AC, incandescent lamps 2000W. No standby loss. For flush mounting. 45 mm long, 45 mm wide, 18 mm deep. State-of-the-art hybrid technology combines the advantages of wear-free electronic control with the high performance of special relays. Either universal control voltage 8..230V UC at the control input +A1/-A2 or 230V with up to 5 mA glow lamp current at the control input with glow lamp symbol (L)/-A2(N). The simultaneous use of two potentials at the control inputs is not permitted. Very low switching noise. No continuous power supply required, thus no standby loss. By using a bistable relay, there is no coil loss and no heating even in the switched-on state. The relay contact can be open or closed at startup and will synchronize on the first operation. If this pulse switch is in a circuit monitored by a field disconnector, it does not require additional base load, but the monitoring voltage must be set to maximum. The electronics have no independent power supply and therefore consume no power in either contact position. Only during the short control pulse of just 0.2 seconds does the control current flow, activating the microcontroller, allowing it to read the last switching state from its non-volatile memory, switching the bistable relay accordingly in the opposite direction and setting the new switching state.
2. Eltako Wireless actuator FSR61-230V
Eltako 1 potential-free switch 10A/250V AC, suitable for incandescent lamps up to 2000 watts, with a delay on release and a pre-warning for switching off, as well as a permanent light function that can be activated. Encrypted radio, bidirectional radio, and repeater function can be enabled. Standby loss is only 0.8 watts. Designed for installation. Dimensions: 45 mm long, 45 mm wide, 33 mm deep. The switching state is maintained in the event of a power supply failure. Upon restoration of the power supply, it will be defined as switched off. After installation, wait for the automatic short synchronization before connecting the switched load to the network. In addition to the radio control input via an internal antenna, this radio actuator can also be locally controlled with a conventional control button that may be installed beforehand. A glow lamp current is not permitted. Encrypted sensors can be learned in. Bidirectional radio and/or a repeater function can be activated. Any state change and received central control telegrams will then be confirmed with a radio telegram. This radio telegram can be learned into other actuators, the GFVS software, and universal displays. Scene control: With one of the four control signals from a button learned as a scene button with a double rocker, multiple FSR61 units can be switched on or off as part of a scene. The upper rotary switch in the LRN position allows for learning up to 35 radio buttons.
3. Eltako Dimmer
With control inputs for light switches and light sensors. To protect the lamps, the switching occurs at zero crossing with soft on and soft off. In addition to the minimum brightness, the dimming speed can also be adjusted, which simultaneously changes the duration of the soft on and soft off. In the snooze function, the set value is dimmed down to the minimum brightness and then switched off, while the children's room function gradually brightens up to the set brightness level. Short control commands turn the light on/off, while continuous controls adjust the brightness up to the maximum value. Suitable for resistive, inductive, and electronic loads, which are automatically detected. If energy-saving lamps are to be dimmed, the function rotary switch should be set to ESL. This takes into account the special conditions for dimmable energy-saving lamps. For example, the switching-on process is optimized, and the dimming speed changes logarithmically; a children's room setting is not possible.
4. Eltako EUD61NPL-230V
Without an N-connection, this power MOSFET operates up to 200 W with a standby loss of only 0.5 watts. It features control connections for light switches, allowing for adjustable minimum brightness, operating mode, and dimming speed. Designed for ceiling installation, it measures 45 mm in length, 45 mm in width, and 18 mm in depth. This universal dimmer switch is suitable for R and C loads up to 200 W, depending on ventilation conditions. It supports dimmable ESL and 230 V LED lamps in "phase-cut" mode up to 200 W or in "phase-angle" mode up to 40 W, also depending on ventilation conditions. For dimmable 230 V LED lamps that glow slightly when turned off, a basic load element (GLE) must be connected in parallel with the lamp.
5. Eltako Decentralized
Eltako Decentralized Actuator PL-SAM1L
Manufacturer: Eltako
Designation: Decentralized actuator with sensor input
Type: PL-SAM1L
KNX bus system: no
KNX wireless bus system: no
Wireless bus system: no
LON bus system: no
Powernet bus system: yes
Other bus systems: none
Bidirectional wireless: no
Mounting type: Flush-mounted
Local/manual operation: yes
With LED display: yes
Max. switching power: 2000 W
Max. LED switching power: 400 W
Output power: 2000 W
Suitable for C-load: yes
Max. number of switching outputs: 1
Max. switching current: 10 A
Rated current: 10 A
Rated operating voltage: 230 V
Different phases connectable: no
With bus coupling: yes
Bus module removable: no
Min. depth of device box: 25 mm
Modular expansion option: no
Eltako Decentralized Actuator PL-SAM1L: Additional details
Powerline actuator with 1 channel and sensor input. Dimensions: 53 x 43 mm, 25 mm deep, designed for installation in 58 mm switch boxes. Usable as a pulse switch or relay. 1 normally open contact, not potential-free, 10 A/250 V AC, for incandescent lamps up to 2000 watts. Sensor input 230 V. Standby loss only 0.5 watts. For control and switching at the same location. For address assignment, there are two rotary switches on the front: The left rotary switch determines the group address g with 16 alphabetical values from A to P. The right rotary switch determines the element address e with 16 numerical values from 0 to 15. Above that, there is a slide switch as a configuration switch with positions 0, 1, and 2. To the left of the rotary switches is a red LED that indicates all activities. Next to it is the reset button and to its right is a service pin. Functions according to the operating manual. The upper connection terminals are plug terminals for conductor cross-sections from 0.2 mm² to 1.5 mm².
6. Eltako FHK61-230V radio actuator heating-cooling relay
Funkaktor heating-cooling relay 230V. 1 potential-free contact, 10A/250V AC. Standby loss of only 0.8 watts. Encrypted radio, bidirectional radio, and repeater function can be activated. For installation mounting. 45 mm long, 45 mm wide, 33 mm deep. In the event of a power failure, the switching state is maintained. Upon restoration of power, it will be defined as switched off. After installation, wait for the automatic short synchronization before connecting the switched load to the network. This heating-cooling relay processes information from radio temperature controllers or sensors. It can be supplemented with window-door contacts, motion detectors, window handle sensors FFG7B-rw, and radio push buttons. The potential-free working contact controls valves. Starting from manufacturing week 11/14, encrypted sensors can be learned in. Bidirectional radio and/or a repeater function can be activated. Any change in function (normal operation, reduced operation, off) is confirmed with a radio telegram. This radio telegram can be learned into the GFVS software. Upper rotary switch for operating modes. The LED accompanies the learning process according to the operating instructions and indicates radio control commands during operation by briefly flashing.
7. Eltako Funk-Lichtaktor
Wireless light actuator 10A/250V AC. Impulse switch with 1 NO contact, potential-free. 230V LED lamps and ESL up to 200W, 230V incandescent and halogen lamps 1000W. Standby loss only 0.4 watts. For recessed mounting. 49x51mm, 20mm deep. The connection terminals are plug-in terminals for conductor cross-sections from 0.2mqm to 2.5mqm. Up to 32 radio universal push-buttons, radio directional push-buttons, radio central control push-buttons and motion sensors can be taught-in using the convenient jog technology. Bidirectional radio can be activated. Distance between control connections/contact 6 mm. Supply, switching and control voltage local 230V. If the supply voltage fails, the switching position is retained. When the supply voltage is restored, it is switched off in a defined manner. After installation, wait for the short automatic synchronisation before connecting the switched load to the mains. In addition to the radio control input via an internal antenna, this radio actuator can also be controlled locally with a conventional 230V control button mounted in front of it. A glow lamp current is not permitted.
8. Eltako ER61-UC
No standby loss. Suitable for flush and surface mounting. 45 mm long, 45 mm wide, 18 mm deep. State-of-the-art hybrid technology combines the advantages of wear-free electronic control with the high performance of special relays. Universal control voltage of 8 to 230 V UC. Very low switching noise. The use of a bistable relay means there is no coil loss and no heating even when switched on. The relay contact can be open or closed at startup and will synchronize upon the first activation. This relay is not suitable for feedback with the switching voltage of a dimmer switch. Only use relays ESR12DDX-UC, ESR12NP-230V+UC, or ESR61NP-230V+UC for this purpose. The electronics have no independent power supply and therefore no standby loss. Only when the control contact is closed is the microcontroller activated, which switches the bistable relay in the correct direction. When the control contact is opened or the control voltage drops, it switches back.
9. Eltako Radio blind and shutter actuator
Radio-controlled blind and shutter actuator 1+1 switch 4A/250V AC, not potential-free, for a shading element motor 230V AC. Standby loss only 0.6 watts. For flush mounting. Dimensions 49x51mm, 20mm deep. The connection terminals are plug terminals for conductor cross-sections from 0.2mm² to 2.5mm². With the convenient tapping technology, up to 32 radio universal switches, radio direction switches, and radio central control switches can be learned. Contact switching at zero crossing. Bidirectional radio can be activated. Supply, switching, and control voltage locally 230V. In the event of a power failure, it is defined to switch off. In addition to the radio control input via an internal antenna, this radio actuator can also be locally controlled with a possibly previously mounted conventional control switch. Either separate local control inputs for up and down as direction switches, or these two inputs can be bridged and controlled with a single switch as a universal switch. The direction change then occurs by interrupting the control signal. A glow lamp current is not permitted. Both a radio switch with the function Up, Stop, Down, Stop as a universal switch and a radio switch like a roller shutter double switch as a direction switch with pressing up for Up and pressing down for Down can be learned. A short tap immediately interrupts the movement. Additionally, central control switches with static priority can be learned. The static priority is only active as long as the radio switch is pressed. With a control signal, e.g., from a radio transmission module learned as a central control switch, the switching position Up or Down and the priority are activated. With priority, because these control signals cannot be overridden by other control signals until the central command is lifted by the end of the control signal.
10. Eltako Follow-up switch NLZ61NP-UC
Delay switch UC. 1 normally open contact, not potential-free, 10A/250V AC. Standby loss is only 0.7 watts. Designed for installation. Dimensions: 45 mm long, 45 mm wide, 18 mm deep. Contact switching at zero crossing to protect the contacts and consumers. State-of-the-art hybrid technology combines the benefits of wear-free electronic control with the high performance of special relays. Universal control voltage of 8 to 230V UC, galvanically isolated from the supply and switching voltage of 230V. By using a bistable relay, there is no coil loss and no heating even when switched on. After installation, wait for the automatic short synchronization before connecting the switched consumer to the power supply. Delay time adjustable from 1 to 12 minutes using the upper rotary switch. Response delay adjustable from 0 to 12 minutes using the lower rotary switch. Function: When the control contact (light switch) is closed, the response delay begins, after which the fan is activated. Once the control contact is opened, and if a set response delay has already elapsed, the set fallback delay (run-on time) begins, after which the fan is switched off. This delay switch can be controlled by all dimmers EUD12 and EUD61, even at the lowest dimming setting.
Product order
See all products