Best selling 3D printer accessories from Prima Creator
This page always stays fresh and updates automatically.
1. Prima Creator Primacreator Silica Gel Pack - Multi Use 10 x 30g
Practical pouch format. The 30g pouches are individually packaged and can be placed exactly where you need moisture protection. Use them with filament spools, electronics cases, or smaller storage boxes. Reliable protection. Just like the larger container, these pouches protect your materials from moisture and prevent the issues that arise when filament absorbs moisture. Reusable and sustainable. After use, the pouches can be dried and reactivated, providing a long lifespan and reducing waste compared to single-use products.
2. Prima Creator PrimaCreator Air Tight Filament Storage Set
PrimaCreator Airtight Filament Storage Set
Sealing your filament spools in a vacuum-sealed bag is a great way to protect them. The bag prevents dirt, dust, and especially moisture from reaching your filament. Keeping your filament sealed and dry is the best way to protect it and maintain its properties. This is particularly important for hygroscopic filaments like Nylon (PA) and PVA. By properly sealing and storing your filaments in a dry environment, you extend their shelf life and ensure that the quality of your prints is always as good as possible.
Easy to use:
The storage set is very easy to use. Place the filament spool in a vacuum bag, add a silica gel packet and a moisture indicator, seal the bag, and use the pump to remove the air. Hold the air valve against a flat surface to ensure a tight seal with the pump. The valve is self-sealing for ease of use. Make sure to position the moisture indicator where you can easily monitor it. As long as the dots on the indicator remain brown, your filament is safe and dry. If the indicator starts to turn blue, there may be moisture in the bag, and you should repackage the spool with a new silica gel packet. The vacuum bags are resealable and can be reused.
Each set includes:
1x Vacuum pump
10x Vacuum bags - 350 x 310 mm (suitable for most 1 kg filament spools)
15x Moisture indicators
15x Silica gel packets.
Additional vacuum bags, moisture indicators, and silica gel packets can be purchased separately.
3. Prima Creator PRIMACREATOR FlexPlate coated PEI 332 x 340mm
PrimaCreator FlexPlate - Powder Coated PEI
The new powder-coated FlexPlate from PrimaCreator consists of three parts. The first is the magnetic surface that attaches to the printer bed. The second and third parts are the high-quality spring steel sheet coated with a plate of premium PEI Ultem. The FlexPlate - Powder Coated PEI is the perfect surface for printing; it is very durable and easy to handle. The best part is that your prints can be easily removed thanks to the flexible plate. A slight bend is all it takes for the print to release.
The PrimaCreator FlexPlate - Powder Coated PEI is based on a ferrite core, which is significantly more heat-resistant than neodymium magnets. This FlexPlate can withstand temperatures up to 130 °C, making it suitable for use with ABS. PrimaCreator's PEI Ultem (Polyetherimid) is a reusable, relatively maintenance-free build surface for ABS (with a heated bed) and PLA (hot or cold), but it also works excellently with other materials like metal, wood, PETG, ABS+, and many more. You do not need additional adhesives like glue or tape. PEI is attractive because it does not require surface treatment, making it easy to work with. Additionally, no support rafts are needed for printing on PEI, as parts adhere directly to the surface without issues.
How to use: Unpack your FlexPlate, attach the magnetic surface to your print bed, and then place the spring steel plate with the attached PEI on the magnetic surface. Remove the protective film from the PEI and realign your print bed. Now you can start printing. The parts should release from the surface almost effortlessly. PLA does not require heat, but it helps to warm the heated bed to 45 °C. You do not need glue, but if you plan to print something large or long-term, we recommend using PrimaFix adhesive.
4. Prima Creator RepRap M6 Brass Nozzle 3mm - 0,6 mm - 1 pcs
Premium Nozzles
The Premium Nozzles from PrimaCreator are a range of replacement nozzles that can make a bigger difference in the outcome than you might think. A high-quality nozzle is like a sharp pencil; you need it to achieve a good print.
All nozzles from PrimaCreator are made from high-quality brass or steel (depending on the type) and are manufactured in a state-of-the-art factory. All nozzles are produced with a tolerance of less than ± 0.01 mm. This means that the filament has a very smooth and clear surface when extruded, which naturally leads to better prints. After this process, the material undergoes an ultrasonic cleaning bath and is then cleaned again and protected against surface oxidation.
The nozzle is now shaped with millimeter precision, with a tolerance of less than ± 0.01 mm. Removing sharp edges from the nozzles is a very important step, as this greatly affects the result. If too many sharp edges remain on the nozzle, it becomes more susceptible to clogs. Therefore, it is crucial that the nozzle is very smooth and clean before use. In each batch, some nozzles are selected and cut in half to ensure that all specifications are met and that the surface is in perfect condition. The nozzles are then inspected one last time and individually packaged in a protective box - ready for shipping to you.
Recommendations
To achieve the best results and optimal print quality, we strongly recommend re-leveling the build plate after switching to a new nozzle. Please note that a PrimaCreator nozzle may be compatible with your printer, but the distance between the nozzle and the build plate needs to be adjusted.
3D printer accessories
Quantity discount
CHF10.70 per piece for 2 units
Prima Creator RepRap M6 Brass Nozzle 3mm - 0,6 mm - 1 pcs
Blast pipe
5. Prima Creator PrimaCreator CR-10S Pro Brass Nozzle 0,8 mm - 1 pcs
Premium Nozzles
The Premium Nozzles from PrimaCreator are a range of replacement nozzles that can make a bigger difference in your results than you might think. A high-quality nozzle is like a sharp pencil; you need it to achieve good prints.
All nozzles from PrimaCreator are made from high-quality brass or steel (depending on the type) and are manufactured in a state-of-the-art facility. All nozzles are produced with a tolerance of less than ± 0.01 mm. This means that the filament has a very smooth and clear surface when extruded, which naturally leads to better prints. After this process, the material undergoes an ultrasonic cleaning bath and is then cleaned again and protected against surface oxidation.
The nozzle is now shaped with millimeter precision, with a tolerance of less than ± 0.01 mm. Removing sharp edges from the nozzles is a very important step, as it significantly affects the results. If too many sharp edges remain on the nozzle, it becomes more prone to clogs. Therefore, it is crucial that the nozzle is very smooth and clean before use. In each batch, some nozzles are selected and cut in half to ensure that all specifications are met and that the surface is in perfect condition. The nozzles are then inspected one last time and individually packaged in a protective box - ready for shipping to you.
Recommendations
To achieve the best results and optimal print quality, we strongly recommend re-leveling the build plate after switching to a new nozzle. Please note that a PrimaCreator nozzle may be compatible with your printer, but the distance between the nozzle and the build plate needs to be adjusted.
3D printer accessories
Quantity discount
CHF10.70 per piece for 2 units
Prima Creator PrimaCreator CR-10S Pro Brass Nozzle 0,8 mm - 1 pcs
Replacement parts
6. Prima Creator PrimaCreator Nozzle Cleaning Kit
Nozzle cleaning set for 3D printers. Each set includes 12 cleaning needles in five different sizes and lengths, a cleaning wire for the feed path, and a pair of tweezers.
3D printer accessories
Quantity discount
CHF8.05 per piece for 2 units
Prima Creator PrimaCreator Nozzle Cleaning Kit
Cleaning
7. Prima Creator PrimaCreator Zortrax Hardened Nozzle for M200/M300 - 0,8 mm - 1 pcs
Premium Nozzles
The Premium Nozzles from PrimaCreator are a range of replacement nozzles that can make a bigger difference in the results than you might think. A high-quality nozzle is like a sharp pencil; you need it to achieve a good print.
All nozzles from PrimaCreator are made from high-quality brass or steel (depending on the type) and are manufactured in a state-of-the-art factory. All nozzles are produced with a tolerance of less than ± 0.01 mm. This means that the filament has a very smooth and clear surface when extruded, which naturally leads to better prints. After this process, the material undergoes an ultrasonic cleaning bath and is then cleaned again and protected against surface oxidation.
The nozzle is now shaped with millimeter precision, with a tolerance of less than ± 0.01 mm. Removing sharp edges from the nozzles is a very important step, as this significantly impacts the results. If too many sharp edges remain on the nozzle, it becomes more susceptible to clogs. Therefore, it is essential that the nozzle is very smooth and clean before use. In each batch, some nozzles are selected and cut in half to ensure that all specifications are met and that the surface is in perfect condition. The nozzles are then inspected one last time and individually packaged in a protective box—ready for shipping to you.
Recommendations
To achieve the best results and optimal print quality, we strongly recommend re-leveling the build plate after switching to a new nozzle. Please note that a PrimaCreator nozzle may be compatible with your printer, but the distance between the nozzle and the build plate needs to be adjusted.
3D printer accessories
Quantity discount
CHF14.20 per piece for 2 units
Prima Creator PrimaCreator Zortrax Hardened Nozzle for M200/M300 - 0,8 mm - 1 pcs
Replacement parts
8. Prima Creator PrimaCreator FlexPlate - coated PEI 310x310mm
PrimaCreator FlexPlate - Powder Coated PEI
The new powder-coated FlexPlate from PrimaCreator consists of three parts. The first is the magnetic surface that attaches to the printer bed. The second and third parts are the high-quality spring steel sheet coated with a plate of the finest PEI Ultem. The FlexPlate - Powder Coated PEI is the perfect surface for printing; it is very durable and easy to handle. The best part is that your prints can be easily removed thanks to the flexible plate. A slight bend is all it takes for the print to release.
The PrimaCreator FlexPlate - Powder Coated PEI is based on a ferrite core, which is significantly more heat-resistant than neodymium magnets. This FlexPlate can easily withstand temperatures up to 130 °C, making it suitable for use with ABS. PrimaCreator's PEI Ultem (Polyetherimid) is a reusable, relatively low-maintenance build surface for ABS (with a heated bed) and PLA (hot or cold), but other materials such as metal, wood, PETG, ABS+, and many others also work excellently. You don't need additional adhesives like glue or tape. PEI is attractive because it does not require surface treatment and is therefore easy to work with. Additionally, no support structures are necessary for printing on PEI, as the parts adhere directly to the surface without issue.
How to use: Unpack your FlexPlate, attach the magnetic surface to your print bed, and then place the spring steel plate with the attached PEI on the magnetic surface. Remove the protective film from the PEI and re-level your print bed. Now you can start printing. The parts should release from the surface almost effortlessly. PLA does not require heat, but it helps to warm the heated bed to 45 °C. You don't need glue, but if you want to print something large or long-term, we recommend using PrimaFix adhesive.
9. Prima Creator RepRap M6 Mixed Size Hardened 3mm - Nozzle x 4
Premium Nozzles
The Premium Nozzles from PrimaCreator are a range of replacement nozzles that can make a bigger difference in the outcome than you might think. A high-quality nozzle is like a sharp pencil; you need it to achieve good prints.
All nozzles from PrimaCreator are made from high-quality brass or steel (depending on the type) and are manufactured in a state-of-the-art factory. All nozzles are produced with a tolerance of less than ± 0.01 mm. This means that the filament has a very smooth and clear surface when extruded, which naturally leads to better prints. After this process, the material undergoes an ultrasonic cleaning bath and is then cleaned again and protected against surface oxidation.
The nozzle is now shaped with millimeter precision, with a tolerance of less than ± 0.01 mm. Removing sharp edges from the nozzles is a very important step, as it significantly affects the outcome. If too many sharp edges remain on the nozzle, it becomes more prone to clogs. Therefore, it is essential that the nozzle is very smooth and clean before use. In each batch, some nozzles are selected and cut in half to ensure that all specifications are met and that the surface is in perfect condition. The nozzles are then inspected one last time and individually packaged in a protective box - ready for shipping to you.
Recommendations
To achieve the best results and optimal print quality, we strongly recommend re-leveling the build plate after switching to a new nozzle. Please note that a PrimaCreator nozzle may be compatible with your printer, but the distance between the nozzle and the build plate needs to be adjusted.
3D printer accessories
CHF30.90
Prima Creator RepRap M6 Mixed Size Hardened 3mm - Nozzle x 4
Blast pipe
10. Prima Creator P120 Hardened Nozzle 0,6 mm - 1 pcs
Premium Nozzles
The Premium Nozzles from PrimaCreator are a range of replacement nozzles that can make a bigger difference in your results than you might think. A high-quality nozzle is like a sharp pencil; you need it to achieve good prints.
All nozzles from PrimaCreator are made from high-quality brass or steel (depending on the type) and are manufactured in a state-of-the-art factory. All nozzles are produced with a tolerance of less than ± 0.01 mm. This means that the filament has a very smooth and clear surface when extruded, which naturally leads to better prints. After this process, the material undergoes an ultrasonic cleaning bath and is then cleaned again and protected against surface oxidation.
The nozzle is now shaped with millimeter precision, with a tolerance of less than ± 0.01 mm. Removing sharp edges from the nozzles is a very important step, as it significantly affects the results. If too many sharp edges remain on the nozzle, it becomes more susceptible to clogs. Therefore, it is crucial that the nozzle is very smooth and clean before use. In each batch, some nozzles are selected and cut in half to ensure that all specifications are met and that the surface is in perfect condition. The nozzles are then inspected one last time and individually packaged in a protective box - ready for shipment to you.
Recommendations
To achieve the best results and optimal print quality, we strongly recommend re-leveling the build plate after switching to a new nozzle. Please note that a PrimaCreator nozzle may be compatible with your printer, but the distance between the nozzle and the build plate needs to be adjusted.
3D printer accessories
Quantity discount
CHF14.20 per piece for 2 units
Prima Creator P120 Hardened Nozzle 0,6 mm - 1 pcs
Blast pipe
Product order
See all products