Best selling Metrology from Jumo
This page always stays fresh and updates automatically.
1. Jumo Inductive
Jumo Inductive Transmitter 00458083
Manufacturer: Jumo
Designation: Inductive Transmitter
Type: 00458083
Design: Inductive
Insertion Length: 67 mm
Max. Pressure: 10 bar
Max. Temperature: 60 °C
Sensor Type: Pt1000
Cell Constant: Other
Electrode Material: Other
Process Connection Design: Other
Process Connection Material: Other
Electrical Connection Design: Other
Angle Connector: No
Cable Length: 0 m
Additional Details: This inductive conductivity/concentration and temperature transmitter with switching contacts and a permanently mounted sensor features 2 freely programmable analog outputs for conductivity and temperature, as well as two potential-free contacts. Up to four measurement ranges and temperature coefficients can be activated. Temperature compensation can be linear, for natural waters, or as a custom characteristic curve (learning function). Additionally, the device includes a desalination control. This device does not have a display or keyboard and can therefore only be operated via setup software. The process connection features a G 1 1/2 PVC union nut, and it has an internal temperature sensor. The power supply is provided via a power supply unit with DC 19...31 V.
2. Jumo Conduktivity Sensor G3/4
Conductivity max. = 1 mS/cm
Conductivity min. = 1 mS/cm
Height = 143 mm
Width = 45 mm
Conductivity measuring cells with a 2-electrode system. Standard measuring cell for determining conductivity in water treatment systems, condensate monitoring, freshwater dosing for galvanizing rinsing baths, air conditioning, and refrigeration. Pressure resistant up to 16 bar. Temperature resistant up to 135 °C. Measuring range: 0 to 1000 μS/cm.
3. Jumo Protective sleeve
Jumo Protective Sleeve 60694017
Manufacturer: Jumo
Description: Protective Sleeve
Installation Length: 120 mm
Type: 60694017
Version: Single
Material of the Immersion Tube: Brass
Material Quality: Other
Pressure Rating: Other
Nominal Diameter of Connection: 1/2 inch (15)
Inner Diameter: 6.5 mm
Outer Diameter: 8 mm
Insertion Length: 120 mm
Suitable for Mano-Thermometers: No
The screw-in protective sleeve made of nickel-plated brass is suitable for a sensor with a diameter of 6 mm. The sleeve is mounted with a G 1/2 thread type A according to DIN 3852/2. The maximum pressure resistance at a temperature of 150 °C is 48 bar.
4. Jumo Conductivity sensor
Jumo Conductivity Sensor 00405886
Manufacturer: Jumo
Designation: Conductivity sensor 0.1-1000 µS/cm, Pt100
Type: 00405886
Design: conductive
Insertion length: 60 mm
Max. pressure: 16 bar
Max. temperature: 135 °C
Sensor type: Pt100
Cell constant: 1
Electrode material: Stainless steel 316 (1.4435)
Process connection design: other
Process connection material: Stainless steel 316 (1.4435)
Electrical connection design: other
Angle connector: yes
Cable length: 0 m
This conductive conductivity sensor has a cell constant of K=0.1 (for measurement ranges of 0.1 to 1000 µS/cm) and features a Pt100 measuring element in a two-wire configuration. Installation is done via the process connection clamp DN25 made of stainless steel (1.4435). An angled device connector according to DIN 43650 is available for the electrical connection. The electrode material is stainless steel (1.4435). The insertion length is 60 mm. The operating temperature ranges from 0 to +135 °C, and the maximum pressure load is 16 bar at 25 °C and 9 bar at 60 °C. This version is a so-called pharmaceutical version with a certificate of compliance according to EN 10204 3.1 for material and roughness, with the roughness of the medium-contacting parts being less than 0.8 µm, accompanied by ASTM certification and sealed in foil.
5. Jumo Temperature sensor with M12x1 plug
Screw-in RTD temperature sensor dTRANS T100. A series of screw-in RTD temperature sensors from Jumo with a compact design. These temperature sensors consist of a sheath with an integrated temperature sensor, a process connection, and an attached housing for the transmitter electronics. Versions are available with or without a transmitter. The integrated programmable 2-wire transmitter converts the resistance value into a current signal. Sheath material: stainless steel. Configuration with setup program via USB interface. IP67, protection against ingress of liquids.
6. Jumo Retractable fitting
With the help of this fitting made of polypropylene, a measuring sensor with a Pg13.5 thread and a length of 225 mm can be removed during the ongoing process. The exchange fitting has a G1A threaded connection as the process connection and a length of 135 mm.
7. Jumo Retrofitting
This accessory is an upgrade that adds 2 logic outputs of 0/12V (optional board) for the DICON touch / AQUIS touch device family.
8. Jumo Transmitter
Jumo Transmitter 202756/15
Manufacturer: Jumo
Designation: Transmitter 617-0000-82/767,941
Type: 202756/15
Design: inductive
Insertion length: 75 mm
Max. pressure: 10 bar
Max. temperature: 140 °C
Sensor type: Pt1000
Cell constant: other
Electrode material: PEEK
Process connection design: other
Process connection material: stainless steel 316 Ti (1.4571)
Electrical connection design: other
Angle connector: no
Cable length: 0 m
Jumo Transmitter 202756/15: additional details
This inductive conductivity/concentration and temperature transmitter with switching contacts and a fixed-mounted sensor features two freely programmable analog outputs for conductivity and temperature, as well as two potential-free contacts. Up to four measurement ranges and temperature coefficients can be activated. Temperature compensation can be linear, for natural waters, or as a custom characteristic curve (learning function). Additionally, the device includes a desalination control. The device can be operated via display and keyboard as well as through setup software. For process connection, the device has a hygienic sensor made of PEEK material with a Clamp 2 1/2 (ISO 2582). The power supply is provided via a power supply unit with DC19...31V.
EAN: 4053877005483.
9. Jumo Immersion fitting
The Jumo immersion fitting is a precise accessory for measurement technology, specifically designed for measuring sensors with a Pg13.5 threaded connection. With a length of 1000 mm and a diameter of 40 mm, it offers a reliable solution for various applications. The fitting is suitable for a temperature range of 0 to +95 °C, making it versatile. Installation is straightforward with pipe clamps, which simplifies the setup process. This immersion fitting is available both as an accessory and as a replacement part, meeting the high-quality standards typical of products from Germany.
- Easy installation with pipe clamps
- Reliable temperature range of 0 to +95 °C
- Compatible with measuring sensors Pg13.5.
10. Jumo 452747 Bayonet counterpart
Jumo Bayonet Counterpart (SW) 00452747
Manufacturer: Jumo
Description: Bayonet counterpart (SW) D=12/8.5mm, L=40/10mm
Type: 00452747
Accessory/Spare part type: other
Accessory: yes
Spare part: yes
The bayonet counterpart in round design (SW) is made of material No. 2.0401.20, nickel-plated brass. It features a process connection with a thread M 12 x 1 and a screw-in length of 10 mm. The counterpart is used for a 12 mm bayonet closure for the installation of plug-in resistance thermometers and thermocouples. The outer diameter is 12 mm and the inner diameter is 8.5 mm. The total length of the counterpart is 40 mm.
Product order
See all products