Top rated Thermal grease

1. Thermal Grizzly Kryonaut

The Kryonaut thermal paste is ideally suited for low-temperature cooling applications such as nitrogen or compressor cooling. However, it also performs excellently between a CPU and an air or water cooler. Embedded in a carrier structure are aluminum and tin oxide components that optimally compensate for unevenness on the surfaces of the heat source and the heat sink while providing outstanding thermal conductivity. Unlike many competing products, the Kryonaut does not begin to dry out even at 80 °C. more

Thermal grease

Quantity discount

CHF7.75 per piece for 2 units CHF7750.–/1kg

Thermal Grizzly Kryonaut

12.50 W/m K, 1 g

3879

2. Arctic Silver Thermopaste silver 5 (3.5g)

For better heat transfer between the processor and the fan. Should be used with all processors and fans, unless the fans are equipped with thermal pads or other materials for special heat dissipation. The paste contains silver particles that conduct heat very well. The silver particle content is approximately 99.9%. 3.5 grams is sufficient for about 20 applications. Minimum 9.0 W/m°K. more

Thermal grease

CHF23.90 CHF6828.57/1kg

Arctic Silver Thermopaste silver 5 (3.5g)

9 W/m K, 3.50 g

1497

3. Arctic Thermal compound MX-4 4 gr.with spatula

The surfaces of processor chips and cooler bases are characterized by microscopic irregularities. The Arctic MX-4 thermal paste is made from carbon microparticles that fill these gaps, resulting in extremely high thermal conductivity. This ensures that heat is dissipated quickly and efficiently from the CPU or GPU. With its outstanding performance, the MX-4 is an excellent choice for overclockers and enthusiasts, as well as for other applications where thermal transfer is required. more

Thermal grease

CHF5.70 CHF1425.–/1kg

Arctic Thermal compound MX-4 4 gr.with spatula

8.50 W/m K, 4 g

1475

4. Arctic Mx-4

The Arctic MX-4 is a thermal paste that offers exceptional heat transfer from components to coolers. Like its well-known predecessors in the Arctic MX series, the Arctic MX-4 is specifically designed for overclockers. The MX-4 is very easy to apply. Its new consistency makes it a breeze to apply cleanly on the chip, even with a finger. The electrically non-conductive paste is placed between the CPU/GPU and the corresponding coolers to optimize heat transfer from the chip to the cooler. Since the Arctic MX-4 is metal-free, it eliminates the risk of short circuits, ensuring increased safety for the computer. more

Thermal grease

Quantity discount

CHF5.10 per piece for 2 units CHF1275.–/1kg

Arctic Mx-4

8.50 W/m K, 4 g

1475

5. Arctic MX-4 2019 Edition Thermal Paste

The surfaces of processor chips and cooler bases are characterized by microscopic irregularities. The Arctic MX-4 thermal paste consists of carbon microparticles that fill these gaps, resulting in extremely high thermal conductivity. This allows heat to be dissipated quickly and efficiently from the CPU or GPU. With its outstanding performance, the MX-4 is an excellent choice for overclockers and enthusiasts, as well as for other applications where thermal transfer is required. more

Thermal grease

CHF26.– CHF577.77/1kg

Arctic MX-4 2019 Edition Thermal Paste

8.50 W/m K, 45 g

1475

6. Arctic Cooling thermal paste MX-4 (8 gr.with

Thermal grease

−12%

CHF20.70 was CHF23.40

Arctic Cooling thermal paste MX-4 (8 gr.with

1475

7. Arctic Cooling MX-4 - Thermal compound

The Arctic MX-4 thermal paste is a high-performance thermal interface material specifically designed for efficient heat transfer between processors and cooling systems. With a density of 2.5 g/cm³ and a thermal conductivity of 8.5 W/m K, this paste offers excellent thermal efficiency that contributes to optimizing cooling performance. The Arctic MX-4 is non-electrically conductive, minimizing the risk of short circuits during application. Weighing 45 grams, it is ideal for multiple applications, whether in the PC building industry or for maintaining existing systems. The viscosity of 870 Poise ensures easy handling and application, allowing for an even distribution on surfaces. Made in China, the Arctic MX-4 is a reliable choice for anyone seeking an effective and safe solution for heat dissipation. more

Thermal grease

CHF31.65 CHF703.34/1kg

Arctic Cooling MX-4 - Thermal compound

8.50 W/m K, 45 g

1475

8. Arctic Silver ArctiClean 30+30ml

Fighting with stubborn residues on the CPU or GPU cooler after changing the CPU or graphics card is now a thing of the past. Often, the old thermal paste or thermal pad is so firmly dried onto the cooler that it can be incredibly frustrating. Many times, one had to resort to mom's nail polish remover. Stress was inevitable, and the results were not always satisfactory.

Arctic has addressed this issue and developed ArctiClean, a two-phase cleaner that easily and efficiently dissolves even the most stubborn thermal pads and thermal paste from CPUs and coolers, while the second phase prepares the surface for the application of new thermal material.

The thermal pad/paste remover ArctiClean 1 is a non-toxic, biodegradable solvent. The liquid is made from extracts of citrus fruits and soy. The scent can even be described as pleasant.

ArctiClean 2 is designed to prepare the surface cleaned with ArctiClean 1 (cooler, CPU, etc.) for new thermal paste and to remove any residues of ArctiClean 1 and/or other cleaning agents. This also helps to reduce the corrosion process of copper and aluminum.

Caution! Please pay attention to the manufacturer's warnings before use!

Contents of the package:
- 30 ml remover
- 30 ml preparation liquid. more

Thermal grease

CHF14.90 CHF186.25/1kg

Arctic Silver ArctiClean 30+30ml

80 g

519

9. Thermal Grizzly Conductonaut liquid metal

Overclockers, watch out. With the paste, the temperature of the processor can be lowered again by a few degrees without having to buy a new cooler. The application of the liquid metal is also surprisingly simple, especially as the manufacturer already includes the necessary accessories in the scope of delivery. If the use is still new at the first time, it goes at the latest from the second application quickly by the hand. Very good.

In addition, the Thermal Grizzly Conductonaut is extremely productive. The filling quantity of one gram of liquid metal is sufficient for far more than 10 applications. And if there is too much liquid metal on the processor, it can simply be sucked back into the syringe. The correct dosage is therefore very easy to handle. On average, half a grain of rice is sufficient for one processor.

Important: The Conductonaut must not be used with contact surfaces made of aluminium. Recommended materials are copper, nickel, silver and other metals. In addition, the Thermal Grizzly Conductonaut Heat Conducting Paste should be stored in its original packaging in dry rooms at room temperature. more

Thermal grease

Quantity discount

CHF12.20 per piece for 2 units CHF12 200.–/1kg

Thermal Grizzly Conductonaut liquid metal

1 g

523

10. Thermal Grizzly Kryonaut Extreme Thermal Paste

Thermal Grizzly from Hamburg is a German brand dedicated to combating high temperatures and poor heat transfer. The goal is to supply the overclocking community with high-performance thermal products that remain a weak point. However, the product portfolio can also be used for better and quieter cooling of gaming computers, workstations, mini-PCs, and many other purposes. In addition to enabling higher clock rates, better thermal products provide quieter cooling and a longer lifespan for the components being cooled.

The thermal paste named Kryonaut Extreme targets extreme overclockers with its outstanding thermal conductivity. As the name suggests, it is ideal for low-temperature cooling methods such as nitrogen or compressor cooling. Compared to the Kryonaut thermal paste, the finer base particles of Kryonaut Extreme reduce the risk of cracks due to the high temperature differences in nitrogen cooling, thereby maintaining thermal conductivity. Kryonaut Extreme is suitable for particularly low temperatures down to -250 degrees Celsius.

Embedded in a carrier structure are tin oxide components and particularly fine nano-alumina particles that optimally compensate for irregularities on the surfaces of the heat source and heatsink while providing exceptional thermal conductivity. Additionally, Kryonaut Extreme is characterized by not drying out even at a high temperature of 80 degrees Celsius and being non-electrically conductive.

The Kryonaut Extreme thermal paste comes in a syringe containing 2 g, sufficient for approximately 6 applications—this, of course, depends on the amount used, the skill of the user, and the size of the CPU. The package also includes an applicator for precise application and distribution of the Thermal Grizzly Kryonaut Extreme. more

Thermal grease

CHF23.95 CHF11 975.–/1kg

Thermal Grizzly Kryonaut Extreme Thermal Paste

14.20 W/m K, 2 g

384