CHF33.60 currently CHF51.95 new
Phanteks Vertical GPU bracket
Questions about Phanteks Vertical GPU bracket
What would you like to know?
0 questions and answers
yes, the bracket works without any problem with a rtx 3060. i use this bracket for my rtx 3080ti. you need 6 slots. important! if you have cross struts at the slots, you have to cut them out. i have an o11 dynamic housing from lian li. with this housing, nothing had to be cut out.
Helpful answer
Yes, this should be possible, but the included riser cable is only pcie 3.0.
Basically, it is compatible with every housing. With some you just have to cut away the struts in the front. After that it fits without any problem.
I would recommend the cooler master vertical kit, which I have already installed several times. Looks nicer and better finished
I recently bought it and it has the standard dimensions of most cases, but unfortunately I haven't found any information on what the Bracet is compatible with.
First check whether you can remove the horizontal braces on the case where the connections for the graphics card are. If not, it won't work.
Hope this helps you a little :)
No, the 5000x has fixed struts.
Hello Sa. Personeni
No, the bracket does not fit in the O11 Dynamic housing. Bought it too and tested it. Now it is lying around... LianLi needs an expensive bracket from the manufacturer itself...
Helpful answer
I didn't need a GPU bracket with my ROG Helios case. It even comes with a bracket ;-) so you don't need to buy one. I have my Graka without bracket directly in the Helios housing and holds tip top! Greetings
Former employee
5 years ago
This product is compatible with all cases with an 'open' PCI slot design. However, you may need to make modifications to your case to install this product.
Helpful answer
Nope, doesn't work. I also ordered this product for the NZXT H510 Elite, but unfortunately you can't remove the grilles from the case. Unless you remove them manually with a saw...
yes it is compatible
Hello... Yes, it covers the pcie slots. But there are mainboards that have a pcie 1x first and then the pcie 16x for the graka.
Which mainboard do you have?
Helpful answer
So I speak from experience: stay away from risers! I've had two recently and there were always problems.
Vertical GPUs are cool, sure, but the risers are simply not stable.
It's better to connect the graphics directly to the mainboard.
It should work! At worst you have to do some minor modifications with the dremel!
Remember that the cable is pcie 3.0 !!!!
Yes, as long as the 3090 has 2 slot connectors, it can be connected to this bracket. However, since the coolers of the 3090 models are very large, the PC case must be large enough. Otherwise, the side panel may no longer be able to be closed.
I don't think that will work. I would recommend downloading the Enthoo 719 manual from the Phantek site and looking at the bracket assembly on page 29 to decide for yourself.
Helpful answer
It is perfectly possible to use a PCIE 4.0 card (e.g. RTX 3080) on a PCIE 3.0 motherboard (e.g. all Z490 chipset motherboards). It should also be possible to use this bracket with a PCIE 4.0 graphics card, the riser being just an "extension" of the PCIE.
Look at picture 5. If the enclosure has struts between the slots then don't....so not without adjustments! You could cut out the struts with a Dremel so that the GPU connections are not obstructed. Peace
No, because there are still rods in the way. These block the connections.
Is the question still relevant?
I recommend asking the customer service directly about this.
https://www.digitec.ch/de...
Then the supplier obviously seems to have problems with the delivery of this product.
Yes, I have it installed with a 2080 ti.
Helpful answer
https://www.youtube.com/watch As far as I know, the Phanteks is belly-light and should work.
7 years ago
Yes, according to our information, it is compatible with all PC cases that have an open PCI slot design.
24 of 24 questions