CHF763.–
Netgear Orbi WiFi 6 Mesh System AX6000 (RBK853)
Questions about Netgear Orbi WiFi 6 Mesh System AX6000 (RBK853)
What would you like to know?
0 questions and answers
As far as I could find out, it does not, no. Here is the manufacturer's data sheet: https://www.netgear.de/images...
The Pro version can do VLAN, though, that's what I found out through research.
According to the manufacturer, a maximum of 6 satellites can be connected to one router. However, this must have at least AC standard. According to the manufacturer, the RBK852s are also not compatible with the RBS50y.
Switch off the WLAN of the Swisscom Internet Box, connect an Orbi Mesh Router to a LAN connection of the Swisscom Internet Box. Restart. The entire network is then taken over by the mesh router. Then unplug all devices from the Swisscom Internet Box and connect them to the Mesh Router.
Helpful answer
Yes, this is possible but must be configured via computer. However, this is not necessary as the Orbi automatically assigns the correct frequency band.
Nobody knows
I would recommend that you install the latest firmware and then try again.
I have used the product in three different places and it works fine everywhere.
Good day
Unfortunately, I can't answer this question because I don't understand your question technically enough.
However, I am very satisfied with the Netgear Orbi WiFi 6.
what is the question here?
Helpful answer
Unfortunately, I don't have any experience with this and therefore can't answer the question.
The quickest way to get such answers is here: https://community.netgear.com/t5...
I have had extremely positive experiences there and my system is running as stable as never before.
Helpful answer
I don't know. But I have uninstalled the Orbi again. I kept having dropouts in connection with my UPC modem and tried a lot of things - including installing specialists and probes. None of it worked. I have now bought and installed Asus. It "only" gives 460Mbps instead of Orbi's almost 900Mbps but works fine.
Helpful answer
Yes, the router is compatible with the Sunrise box, the Orbi is simply connected to one of the network ports of the existing box.
It is recommended to switch off the WLAN on the Sunrise Box so that only 1 network is transmitted. Sunrise must explain this in the settings, it is a common function of all WLAN routers.
You can give the Orbi Wifi the name/password as your Sunrise network so that your existing devices will connect easily.
The router can also be configured normally via the IP address, like any other router. It should be mentioned that it does not currently work with Safari 15.1, as the implemented SLL certificate is not recognised by Safari and cannot be bypassed. However, with other browsers, e.g. Chrome, it works without any problems. The Insight app can also be used after the end of the test phase, but a maximum of 2 devices can be managed via it.
No, only the router can act as access points.
I have connected the main module with an Ethernet cable to the first satellite, from there it goes via a Devolo Gigaset to the next room because I don't have a cable there. From the Gigaset satellite via cable then to the second RBK50 satellite. The connection between the main module and both satellites is shown as "wired" in the app and I have the full functionality of the app. I have already carried out FW updates twice.
The first time I set it up with a Wi-Fi connection, and only then did I set up the satellites in their final location and connect them via cable. It was no problem at all. When setting up, the app sometimes did not show the current status of the satellite, this seems to be a timing problem. However, the setup itself worked reliably.
You connect it to the Lan port of your router/modem. The provider doesn't matter. That's the beauty of standards.
Former employee
5 years ago
Please contact your operator for this. Or write us an e-mail. I'm not a technician, so I can't give you any information, and I'm sorry about that.
Hello,
Sorry, but I have no idea. I use a Synology and I have access to it from everywhere.
Helpful answer
I am a layman myself but I will try to answer some of your questions.
Just to clarify before I explain things here, a wireless router consists of three things:
-First, a router that controls the traffic between its own network and the infinite networks that exist.
-Secondly, a netword switch, which controls the traffic between your own devices connected to your network.
-And thirdly, a wireless access point (AP for short), which makes the network wireless and connects wifi enabled devices to the network.
Question 1: This is called triband, this is built in especially in the newer Wifi 6 mesh systems. This allows the different AP's (Access Points) to communicate with each other without affecting the other two bands.
A band can be thought of as a lane on the motorway. Devices are vehicles travelling in these lanes. If you have only two lanes, the different Ap's have to communicate over these lanes and slow down the whole traffic, but can also be slowed down by e.g. a slow Tracktor (an older device).
If you now add another lane that only serves for the communication of the different APs, then they have their peace and can always work undisturbed while all other devices are driving on the other two lanes.
That is why such routers use triband so that they can guarantee the high speeds of the Wlan 6.
2nd question: Such devices exist, but they are less and less built for "normal" houses, because many prefer to have just one connection to the network and the other two ap's can be distributed where they want.
I found these routers, but I'm not sure if they have all the ports like on the first picture.
ASUS ZenWiFi XT8 WiFi 6 AX6600 (2 Pack)
Question 3: Yup every system has a weak point. If the main router fails then nothing works. There are probably expensive routers that you can run redundantly, but for a private network at home I find that almost excessive. But if you're looking for something like this, I recommend you get advice from professionals who can also install such a system at home.
Now what you are looking for:
I've searched around a bit myself and haven't found anything that exactly meets your requirements. There will always be the weak point that if the main router fails the whole system is down.
One possibility would be Ubiquiti https://www.digitec.ch/de...
You can buy everything separately, i.e. router, a network switch and also several Ap's to build up your own system.
But even that will have a weak point.
I hope I could be helpful and have fun building your network :)
Helpful answer
Yes, you can set up the Orbi router as an access point and connect it to the Salt router,
Or set up the Salt router as a bridge and use the Orbit router as a router. But you would have to clarify this with the support from the provider.
Helpful answer
Yes you can do that
2 x yes, after a power failure, the router and Sattelit start up again and the connection is re-established and in the "Schedule" functionality, blocking by the day or minute can be recorded.
Former employee
6 years ago
The desired product will be added to our site shortly. (delay of about 1 month if everything goes as planned)
30 of 33 questions