Questions about Arctic X1-3D

55mm https://www.arctic.de/X1-3D/AEMNT00062A

Correct

Hello I bought the mount for my Xiaomi 34" and it works fine so far. Since the monitor arm also supports the VESA 75x75 fit (which corresponds to the fit of your monitor), there should actually be no problems, since these fits must remain universal ;) Greetings

I only have a light monitor (3.5) kilos hanging on it, but the arm seems extremely solid and stable. In the enclosed operating instructions, it is stated in the specs at the back: "Maximum monitor weight: 15 kg/33 lbs". So a little over 10 kg should go easily.

The Arctic X1-3D monitor mount (AEMNT00062A) is compatible with monitors with VESA 75x75 or 100x100 mounts. For the Samsung Smart Monitor M7 (M70D), you need to check if this monitor has one of these VESA mounts. According to the specifications of the Samsung Smart Monitor M7, it is generally compatible with VESA mounts, but it is advisable to check the exact specifications of the model you own. In general, Samsung Smart Monitor M7 (M70D) are equipped with VESA mounts, making them compatible with Arctic X1-3D support.

Yes, it is possible to attach the "Samsung The Frame QE32LS03C" to the Arctic X1-3D monitor arm (AEMNT00062A), provided that the monitor fulfils the following requirements: - Maximum screen diagonal: The Arctic X1-3D monitor arm supports screens up to 40 inches. - Maximum load capacity: The monitor arm can support up to 10 kg. - VESA mounting: The Samsung The Frame QE32LS03C must have the VESA mounting standards 75 x 75 mm or 100 x 100 mm, which the Arctic X1-3D monitor arm supports. As the Samsung The Frame QE32LS03C has a diagonal measurement of 32 inches and usually has VESA mounting points, it should be able to be attached to the Arctic X1-3D monitor arm without any problems. However, it is always advisable to check the specific VESA dimensions and weight of the monitor to ensure that they match the specifications of the monitor arm.

The Arctic X1-3D (Tables, 40") monitor mount is designed to support monitors up to 40 inches and has a maximum load of 15 kg. To determine compatibility with your Philips Evnia 32M2C5500W monitor, you need to check the dimensions and weight of your monitor. - Dimensions and weight: Check that your screen measures 32 inches or less and weighs less than 15 kg. - VESA mounting: Make sure your screen is compatible with the VESA mounts supported by the X1-3D. The X1-3D generally supports VESA mounts from 75x75 mm to 200x200 mm. If these criteria are met, the Arctic X1-3D monitor mount should be compatible with your Philips Evnia 32M2C5500W screen.

No, because the connections for the monitor are integrated into its stand. If you were to remove and replace the stand, you would have neither power nor HDMI. In other words: no monitor arm fits this monitor. You have to leave the monitor exactly as it is.

You need about 3 cm / 1 inch to mount it to the desk. However, this method substantially limits the screen's maneuverability and the space it takes up for smaller desks. In this case, you need about 25 cm / 10 inches of space behind the desk to position the screen at the edge of the desk.

Moin, it depends on how wide your table is. However, the arm can be rotated/positioned far towards the centre of the table. I hope my answer is helpful. LG

So it probably won't work further back, but it will go right up to the edge. That's what I do with my 34" monitor.

yes I set it up like this.

For the bracket to hold, your tabletop should have an overhang of at least 5 cm. Otherwise, the screw mount of the swivel arm will not attach well. The swivel arm is very good in any case.

Nope, I also have a 43" Dell monitor with the Arctic in use and am super satisfied. Only the table mount is a bit special and could be better.

The Vesa mount would not be a problem, as both the 100 x 100 mm mount, as with the LG 34WK95UP-W, and 75 x 75 mm are supported. However, this monitor mount will not work for you as it is only suitable for monitors up to 10kg, but the LG 34WK95UP-W weighs 12.3kg, which is too heavy.

Yes, it would be compatible with your monitor and strong enough to support it. Your monitor has the following specifications: Vesa 100 × 100, weight (without stand): 7.25 kg

https://www.arctic.de/media/17/92/dd/1690892615/Spec_Sheet_X1-3D_DE.pdf

Yes, your monitor supports VESA and therefore this mount is compatible.

Yes, everything you need is included in the scope of delivery.

I have about 7cm between the wall and the back of my screen.

Yes. I use it with a 32"

Hi, I have this mount and I’m using it with a similar Benq monitor (also 32 but don’t remember the model). Mine is around the same weight and the mount seems to be working well.

If by "would the mount still fit" you mean whether the mount will support your monitor, then I mean no: The payload is clearly stated as 10 kg --> Maximum monitor weight: 22 lbs | 10 kg.

when fully extended, I have a distance of approx. 50cm between the edge of the table and the bottom two screws of the bracket

You can find everything on the manufacturer's website: https://support.arctic.de/x1-3d/docs

Hello! No, not at all, I had already attached the Arctic stand very close to the edge of the tabletop because I had a soundbox in the middle .... I hope that I was able to help! Greetings U.Hofmann